Rod seals manufacturer and supplier 2024: Basics of fluid pump sealing – A mechanical seal is simply a method of containing fluid within a vessel (typically pumps, mixers, etc.) where a rotating shaft passes through a stationary housing or occasionally, where the housing rotates around the shaft. When sealing a centrifugal pump, the challenge is to allow a rotating shaft to enter the ‘wet’ area of the pump, without allowing large volumes of pressurized fluid to escape. To address this challenge there needs to be a seal between the shaft and the pump housing that can contain the pressure of the process being pumped and withstand the friction caused by the shaft rotating. The gap between the faces on a typical seal is as little as 1 micron – 75 times narrower than a human hair. Because the gap is so tiny, particles that would otherwise damage the seal faces are unable to enter, and the amount of liquid that leaks through this space is so small that it appears as vapor – around ½ a teaspoon a day on a typical application. See more info on o ring manufacturers.
Mechanical seals often need to be used in chemical applications. When confronted with some harsh chemicals, mechanical seals containing elastomers made of Viton, Kalrez or Chemrez can’t hold up. Because PTFE (polytetrafluoroethylene)or as most people know it Teflon ® , has a 0-14 ph range it usually will hold up. Like most materials every choice has an up and a down side. Because PTFE will handle most chemical applications, chemical attack is no longer an issue. One the down side PTFE wedges can cause fretting of your sleeve or shaft if you have not hard surfaced your shaft or sleeve (plasma coating). The stationary element of your seal will require a PTFE gasket. It’s not much good to have a PTFE on the rotary and then use an elastomer on the seat. We have seen it done, and because it is a static application some have gotten away with it, but it is not recommended. Most commonly the seat will be a L-shaped or Clamped mount style to allow space for a PTFE gasket to be used as the secondary sealing element.
Select the appropriate sealing material: There are many types of sealing materials, including many metals, plastics and rubbers. The same material has different performances from different companies. On the other hand, the same seal has different performances in different working conditions or different sealing schemes, so it must be carefully considered when choosing. Note: Be sure to consider seals under the premise of a reasonable sealing scheme, then consider the sealing material, and then consider the seal manufacturer. If you don’t have enough sealing experience, it is best to consider the sealing company first, and let the sealing company consider the sealing scheme and other issues, such as DMS Seals Technology Co.,Limited.
Our structure is simple. Moreover, the seal is easy to manufacture and assemble. One of its remarkable features is its good adaptability to the oscillation and eccentricity of the shaft. The cavity in which it is mounted is compact in size for easy processing. It perfectly overcomes the gap issue caused by the oscillation and rotation of the sealing system when the shaft rotates, and the lip of the oil seal can always be in close contact with the surface of the shaft.
The gasket made by DMS SEALS is uniquely mechanical and thermally stable and it has excellent oxidation resistance. Compared with other thermoplastics, it can be applied to components such as valves and bushings, with higher wear resistance, higher mechanical properties and thermal fatigue resistance. At the same time, it has excellent oil resistance (alkane oil), heat resistance, water resistance, aging resistance, air tightness and excellent adhesion. It is commonly used in media such as water, oil, and natural gas.
Wiper seals are utilized to remove contaminants like moisture, soil, and dust. Some wipers or even scrapers possess a secondary lip utilized to catch any oil which might have bypassed the major seal. The secondary lip can also get rid of any bonded contaminate in the pole surface. These kinds of wipers are usually called double-edged wipers. Metallic scrapers could be used for sub zero temperature software and especially arduous software where foreign substances can deposit the pole.
Leakage of gaskets: There are four types of leakage phenomenon in general gaskets: interface leakage, penetration leakage, diffusion leakage, and damage leakage. Interface leaks: The interface will leak at the sealing interface due to insufficient gasket compression, improper flange joint surface finish, and flange deformation. For interface leakage, it can be prevented by using soft gasket to clamp in the flange face. Penetration leakage: Since most of the soft materials are made of fibers, they are easily soaked by the medium, especially the pressure. Due to capillary phenomenon, the medium will permeate to the low pressure side, forming permeation.
DMS SEALS is a technology enterprise which specialized in the production of seals, the development of seals material and the solution of the sealing of special working condition. We own 120 staffs which including 70 middle and senior technicians. Our factory covers more than 10000 square meters which including 8000 square meters for the workshop. Our production equipment and test equipment are on leading level in the same industry. We are the one of the biggest enterprise who specialized in manufacturing and developing seals in China. We have long time cooperation and communication with many universities and research institutions at home and board. Find extra info on https://www.dmsseals.com/.
DMS Seals is a professional hydraulic seals, industrial mechanical seals manufacturer and oil seal supplier specializing in supplying sealing solutions and various seals & o ring. As a leading custom o ring manufacturer, DMS can support OEM and ODM and can meet customers’ requests. DMS Seals adheres to the tenet of “first-class design, top manufacturing, excellent service” and strive to be an excellent supplier of sealing system solutions. DMS Seals pays the utmost attention to quality to ensure the satisfaction of our cooperative partners.